- 您现在的位置：买卖IC网 > Sheet目录1201 > CDB5467U (Cirrus Logic Inc)BOARD EVAL FOR CS5467 ADC
CS5467
10. E 2 PROM OPERATION
The CS5467 can accept commands from a serial
E 2 PROM connected to the serial interface instead of a
host microcontroller. A high level (logic 1) on the MODE
input indicates that an E 2 PROM is connected. This
makes the CS and SCLK pins become driven outputs.
After reset and after running the initialization program,
the CS5467 begins reading commands from the con-
nected E 2 PROM.
10.1 E 2 PROM Configuration
A typical connection between the CS5467 and a
The CS5467 asserts CS (logic 0), clocks SCLK, and
sends Read commands to the E 2 PROM on SDO.
Command format is identical to microcontroller mode,
except the CS5467 will not attempt to write to the EE-
PROM device. The command sequence stops when the
STOP bit in the Control register ( Ctrl ) is written by the
command sequence.
10.2 E 2 PROM Code
The EEPROM code should do the following:
1. Set any Configuration or Control register bits, such as
HPF enables and phase compensation settings.
2. Write any calibration data to gain and offset registers.
3. Set energy output pulse width, rate, and formats.
4. Execute a Continuous Conversion command.
5. Set the STOP bit in the Control register (last).
Below is an example E 2 PROM code set.
- 7E 00 00 01
Change to page 1.
- 60 00 01 E0
Write Modes Register, turn high-pass filters on.
- 42 7F C4 A9
Write value of 0x7FC4A9 to I1 GAIN register.
- 46 FF B2 53
Write value of 0xFFB253 to V1 GAIN register.
5K
VD
+
E1
E2
CS5467
SCLK
SDI
SDO
MODE CS
Pulse Output
Counter
5K
EEPROM
SCK
SO
SI
CS
- 50 7F C4 A9
Write value of 0x7FC4A9 to I2 GAIN register.
- 54 FF B2 53
Write value of 0xFFB253 to V2 GAIN register.
- 7E 00 00 00
Change to page 0.
- 74 00 00 04
Set LSD bit to 1 in the Mask register.
- E8
Start continuous conversions
Connector to Calibrator
Figure 13. Typical Interface of E 2 PROM to CS5467
would be made to a calibration device, such as a note-
book computer, handheld calibrator, or tester during
- 78 00 01 00
Write STOP bit to the Control register ( Ctrl ) to
terminate E 2 PROM command sequence.
10.3 Which E 2 PROMs Can Be Used?
Several industry-standard serial E 2 PROMs can be used
with the CS5467. Some are listed below:
meter assembly, The calibrator or tester can be used to
control the CS5467 during calibration and program the
required values into the E 2 PROM.
?
?
?
Atmel AT25010, AT25020 or AT25040
National Semiconductor NM25C040M8 or NM25020M8
Xicor X25040SI
These serial E 2 PROMs expect a specific 8-bit com-
mand (00000011) in order to perform a memory read.
The CS5467 has been hardware programmed to trans-
mit this 8-bit command to the E 2 PROM after reset.
42
DS714F3
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CDB5560-2
DEV BOARD FOR CS5560 W/SE INPUT
CDB5571-2
DEV BOARD FOR CS5571 W/SE INPUT
CDB8422
BOARD EVAL FOR CS8422 RCVR
CDB8952T
BOARD EVAL FOR CS8952
CDCE906-706PERFEVM
EVAL MOD PERFORMANCE CDCE906/706
CEVAL-033
BOARD EVAL FOR CVCO33 .3"X.3"
CF37S
COVER FLANGE 37POS FEMALE
CG0402MLC-05LG
SUPPRESSOR ESD 5VDC 0402 SMD
相关代理商/技术参数
CDB5471
制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con
CDB5480U-Z
功能描述:电源管理IC开发工具 CS5480 Eval Board
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
CDB5484U-Z
功能描述:电源管理IC开发工具 CS5484 Eval Board
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
CDB5490U-Z
功能描述:电源管理IC开发工具 CS5490 Eval Board
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
CDB5501
制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5501 - Bulk
CDB5503
制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5503 - Bulk
CDB5504
制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Low Power, 20-Bit A/D Converter
CDB5505
制造商:Cirrus Logic 功能描述:EVAL BD FOR CS5505 - Bulk